New SURTRON 80D

NewItalian production,It has the ability to cut, cut with coagulation as well as monopolar coagulation and microcoagulation,Controlled by a microprocessor, equipped with the most technologically advanced elements and circuits, including LSI microcontrollers, which informs about any problems or about exceeding the recommended working power during cutting or coagulationThey remember the last used settings, thanks to which after restarting the diathermy or changing the work mode it is possible to recall previously used parametersThe volume of signaling the operation of surgical diathermy can be adjusted.Activation of the device can be done using the buttons on the handle or foot pedal, which is equipped with Surtron surgical diathermy.The device can be controlled from the front panel of the device or by using buttons on the work handle.Application of diathermy:Traumatic surgery,Vascular surgery,Dentistry,Dermatology,With first aid,Veterinary (small animals),Diathermy functions:Coagulation - A temperature of 60 to 70ºC in the area around the active electrode causes slow heating of intracellular fluid; Water in the cells evaporates, we get the effect of coagulation and stopping blood flow.Cutting - A temperature of more than 100ºC in the area around the active electrode causes the evaporation of intracellular fluid and destruction of cells. The vapors around the electrode begin a sequence of reactions in the direction of the active electrode. Energy is conducted to neighboring tissues. In this case, such cutting is not equivalent to mechanical cutting. When the temperature reaches 500 ° C, cauterization occurs.Mixed currents - combine cutting and coagulation effects. During the cutting procedure, blood loss is limited and a scab is formed.Operational techniques used with Surtron80D diathermy:Monopolar cutting is cutting biological tissue through a dense high-frequency current, concentrated at the end of the active electrode. When applied by an active electrode, high-frequency current intensively heats the cells, causing them to be destroyed. The cutting effect is obtained by moving the electrode on the tissue and destroying subsequent cells. The movement of the electrode prevents heat from spreading sideways, so that the area of ​​cell destruction is limited to a single line. The best high-frequency cutting current is pure sine wave without modulation. The cutting is then smooth and the thermal effect is small, thanks to which hemostasis occurs only to a small extent. Because the effects of this wave can be precisely controlled, it can be safely used for cutting bones. In addition, since good coagulation during cutting is one of the basic advantages of electrosurgery, a certain level of modulation is also desirable.Monopolar coagulation is hemostasis of small blood vessels by high-frequency current flowing in the active electrode. After reducing the current density and applying a wide-surface electrode to spread energy over a larger area, the effect is to dry the surface cells without penetration, which results in coagulation. Coagulated surface cells then form an insulating coating, protecting against too deep heat penetration during subsequent applications. The current used for coagulation is usually modulated. The degree of modulation depends on the smoothness of the cut, the degree of hemostasis and the likelihood of tissue damage. Greater current modulation promotes less precise cutting and is associated with some risk of damage to deeper tissues, but also provides more effective coagulation.Programs for diathermy:CUT (cutting)The best current for cutting with an electrosurgical knife is a pure sine wave without modulation, i.e. with a 100% duty cycle. Such current is intended for cutting without coagulation.BLEND (mixed current)Mixed coagulation-cutting current is used when deep coagulation together with cutting is required. The current thus obtained is suitable for cutting with coagulation, without the formation of scabs and carbonization.COAG (coagulation)Modulated current is characterized by good surface coagulation properties and at the same time the likelihood of scabs and partial carbonization. The advantage of this type of current is the speed of obtaining the coagulation effect.MICRO (microcoagulation)The MICRO modulated current is intended for coagulation of small blood vessels. The coagulation process is then easier to control and more accurate.Equipment:Reusable handle,Electrode set 5 cm (10 pcs):L1 - thin thin wire electrode,L2 - bent thin wire electrode,L3 - 4mm loop electrode,L4 - 8mm loop electrode,L5 - folded hooked electrode,L6 - bent thin wire electrode,L7 - teardrop electrode,L8 - loop electrode,L9 - 3mm straight ball electrode,L10 - ball electrode. He has issued a valid Technical Passport,

Warranty: 12 months,
Possibility of financing (only Poland): Instalments, Leasing, Loan

If you have any questions, please do not hesitate to contact us!
In case you don’t find the product you are interested in, please get in touch with us and we will do our best to find the perfect solution for YOU.

WE SPEAK ENGLISH

HABLAMOS ESPANOL

WIR SPRECHEN DEUTSCH

ON PARLE FRANCAIS

WIJ SPREKEN DUTCH

WE SPEAK RUSSIAN AND UKRAINIAN